Q69K7-61341 Washer 组合垫圈(G3/4)
Q69K7-60311 Nipple 多路阀回油接管
Q69K7-62001 Hose 吸油胶管
Q79B7-62251 Bolt 铰接螺栓(G3/8)
Q78B7-61381 Washer 组合垫圈(G3/8)
Q69K7-60351 Steel pipe ass’y 多路阀进油钢管总成
Q69K7-60401A Lift hose ass’y 起升胶管总成 1.6t
Q69K7-60411A Lift hose ass’y 起升胶管总成 1.8t
Q69K7-10001 “Gear pump ass’y 齿轮泵总成
(包含29-37)”
Q69K7-60421 Hose H.P. 高压胶管总成
Q69K7-62051 Single direction valve 管式单向阀
JT8021-78051 Nipple 直通接头
Q69K7-60361 Steel pipe ass’y Pt口支架钢管总成
Q69K7-60371 Steel pipe ass’y Tp口支架钢管总成
Q69K7-30201 Controll valve 多路换向阀(全比例) 舒适型(Comfort type)
Q69K7-30211 Controll valve 多路换向阀(单比例) 经济型(Economy type)
Q69K7-60201A Bracket ass’y 多路阀支架总成
B5310-00010 Washer 垫圈10 GB97.1-85
B5050-00010 Washer,lock 垫圈10 GB93-87
B0330-10025 Bolt 螺栓M10x25 GB5783-86
Q69K7-62341A Bolt 铰接螺栓(G3/4)
B8030-08020 Screw 螺钉M8x20 GB70-85
B5050-00008 Washer,lock 垫圈8 GB93-87
B5310-00008 Washer 垫圈8 GB97.1-85
B0330-08020 Bolt 螺栓M8x20 GB5783-86
Q69K7-10181 Gear pump 齿轮泵(18R)
B5050-00010 Washer,lock 垫圈10 GB93-87
B0530-10025 Bolt 螺栓M10x1.25×25 GB5786-86
Q69K7-60211 Flange 高压法兰
B0330-10025 Bolt 螺栓M10x25 GB5783-86
B5310-00010 Washer 垫圈10 GB97.1-85
Z6053-02803 O-ring O型密封圈28×3.55 GB3452.1-92
Z6053-03253 O-ring O型密封圈32.5×3.55 GB3452.1-92
Q78B7-60261 Intake flange 吸油法兰
Q69K7-50201A Oil tank ass’y 液压油箱总成
HP617-52021 Oil tank mat 盖板垫一
22197-52081 Drain plug 放油螺塞
Z6700-03027 Washer 组合垫圈8 JB982-77
G0176-10011 Magnet 磁铁φ68/φ37×14
H24C7-50201 Return oil filter 回油过滤器
B0330-08016 Bolt 螺栓M8x16 GB5783-86
Z6701-00827 Washer 组合垫圈8 JB982-77
Q69K7-50211A Oil tank 液压油箱
Q69K7-50221A Oil filler cap ass’y 油箱盖板总成
Q69K7-50231 Tank cover ass’y(lnc.12-14)加油盖总成
G27Z7-50402 Ventilation cap 透气帽
H24C7-61701 Oil cap ass’y 加油盖
B3010-02016 Pin 销2X16
Q69K7-52121 Oil lever 游标尺
HRD69K8601 Mast hydraulic system 门架管路系统
Q78B0-60701 Nipple(Inc.25) 直通接头(包含25)
D69K8-60011 Steel pipe ass’y 钢管总成Ⅰ(左)
D7B38-62071 Elbow(Inc.26) 直角接头(包含26)
D69K8-60021 Steel pipe ass’y 钢管总成Ⅰ(右)
D69K8-60051 Steel pipe ass’y 前缸缸底钢管总成
D69K8-62141 Lock plate 限位卡板
B5050-00008 Washer,lock 垫圈8 GB93-87
B0330-08020 Bolt 螺栓M8x20 GB5783-86
D69K8-60031 Steel pipe ass’y 钢管总成Ⅱ
B0330-06012 Bolt 螺栓M6x12 GB5783-86
B5050-00006 Washer,lock 垫圈6 GB93-87
HRD69K8611 Hose H.P. 高压胶管 “见表
See op.Parts”
Q78B0-62181 Clip 胶管管卡
B0230-06030 Bolt 螺栓M6x30 GB5782-86
B5050-00006 Washer,lock 垫圈6 GB93-87
D69K8-60041 Steel pipe ass’y 钢管总成Ⅲ
H22N0-92521 Shaft 滑轮轴
D15Y8-62071 Pulley 滑轮
H22N0-88112 Block 垫块
D69K8-60001 Four-wayb ass’y 四通接头总成
D7B38-62061 Flow regulator case 限速阀壳体
SB33C-50 Flow regulator 限速阀
Z6006-01982 O-ring O型密封圈19.8×2.4 JIS B2401
DS2S8-62061 Nipple(Inc.26) 直通接头(包含26)
Z6006-02373 O-ring O型密封圈23.7×3.5 JIS B2401
Z6006-01782 O-ring O型密封圈17.8×2.4 JIS B2401
D69K8-71491 “Belong to attachment
pipe system(SAE) 属具管路系统(美制)”
D69K8-71531A Three-way steel pipe 三通钢管总成1
D69K8-71541A Three-way steel pipe 三通钢管总成2
D69K8-75161 Joint bolt 接头螺栓
D69K8-75171 Washer 组合垫圈(G1/4)
JT8021-96191 Nipple 直通接头
D69K8-71071 Six-way valve 两位六通阀
D69K8-75731 Hose clip 胶管固定卡
B0330-06012 Bolt 螺栓M6x12 GB5783-86
B5050-00006 Washer,lock 垫圈6 GB93-87
Z7801-0603812 Hose H.P. 高压胶管
B1210-06010 Screw 螺钉M6x10 GB818-85
D69K8-71511L “Extend & indend伸缩油缸钢管总成(左)
steel pipe(left)”
D69K8-71511R “Extend & indend伸缩油缸钢管总成(右)
steel pipe(right)”
D69K8-71611A “Main suction 主进油钢管总成1
steel pipe”
D69K8-71621A “Main suction 主进油钢管总成2
steel pipe”
D69K8-71941 Pipe system cover 管路罩盖总成
B5050-00008 Washer,lock 垫圈8 GB93-87
B0330-08016 Bolt 螺栓M8x16 GB70-85
D69K8-75801 Induction plate 属具感应板
D69K8-76201A Induction dead block 属具缓冲感应板
D69K8-71951 Hose hood ass’y 胶管护罩总成
D69K8-75051 Six-way bracket 两位六通阀支架
D69K8-71661L Steel pipe(left) 钢管总成(左)
D69K8-71661R Steel pipe(right) 钢管总成(右)
Z7801-0602412L07 Hose H.P. 高压胶管
B5050-00005 Washer,lock 垫圈5 GB93-87
B8030-05045 Screw 螺钉M5x45 GB70-85
Q78B7-61501 Nipple 直通接头
Q69K7-30221 “Forward shift bidire- 剪叉前移双
ctional balance valve 向平衡阀”
B8030-06060 Screw 螺钉M6X60 GB70-85
D69K8-75321A Balance valve support plate平衡阀支板
D69K8-71641A Steel pipe 钢管总成1
D69K8-71631A Steel pipe 钢管总成2
D69K8-76101 Steel pipe setting plate 钢管固定板
D69K8-71811 Steel pipe stopper 钢管限位总成
B4123-00008 Nut 螺母M8 GB6170-86
B5050-00012 Washer 垫圈12 GB93-87
B4123-00012 Nut 螺母M12 GB6170-86
D69K8-92141 Cable clip 线卡
Z7801-0612512 Hose H.P. 高压胶管
B5310-00005 Washer 垫圈5 GB97.1-85
B8030-05012 Screw 螺钉M5x12 GB70-85
D69K8-75501 Baffle plate 挡板
D69K8-75511 Hose clip 管夹
D69K8-75041 Attachment pulley bracket属具滑轮支架
D69K8-92131A Pulley 滑轮
D69K8-92071 Setting bolt 固定螺栓
B5050-00016 Washer 垫圈16 GB93-87
B4223-00016 Nut 螺母M16 GB6171-86
B5310-00008 Washer 垫圈8 GB97.1-85
D69K8-71791 “Hose stopper bracket 胶管限位
支架总成”
D69K8-76081 Steel pipe 钢管φ14×1.8×70
D69K8-75131 Hose commutator wheel 胶管换向轮
D69K8-71671A “Tilt cylinder 倾斜油缸钢管总成1
steel pipe ass’y”
D69K8-71521A “Tilt cylinder 倾斜油缸钢管总成2
steel pipe ass’y”
Q78B7-61001 “Balance valve block 单向平衡
(Inc.valve core) 阀块(含阀芯)”
D69K8-71701 Elbow 直角接头
Q78B7-61021 Three-way 三通可调向接头
D69K8-71711 Tie-in 过渡接头
D69K8-71731 “Rear cavity
steel pipe ass’y 后腔钢管总成”
D69K8-71721 “Front cavity 前腔钢管总成
steel pipe ass’y”
B0230-06035 Bolt 螺栓M6x35 GB5782-86
B0330-08025 Bolt 螺栓M8x25 GB5783-86
D69K8-92031 Three-clip 三列管夹
D69K8-76091 “Hose stopper 胶管限位支架板
support plate”
D18JH-52061 Bolt 螺栓
D18JH-52021 Pulley 滑轮
D69K8-50001 Extend & indent cylinder 伸缩油缸(左)
D69K8-50011 Extend & indent cylinder 伸缩油缸(右)
D69K8501-01 Earing 耳环
B4735-00024 Small nut 小圆螺母M24x1.5 GB/T810-2000
D69K8501.2-00 Piston rod 活塞杆体
C5B38-42051 Dust ring 防尘圈28x36x5/7
D69K8501-03 Guide 导向套
FU0321K1 Seal ring ISI型轴用密封圈82x36x5
GCX050BJ-10 Snap ring 挡片36x28x3
HRD8S90818-05 Snap ring 挡片45x40x1.25
C00203 O-ring O型密封圈39.4×3.1
Z2113-02825 Bushing 钢背轴承2825
D69K8501.1-00 Cylinder body 缸体
22580-53311 Seal ring 孔用密封圈45x35x6
C51B8-42251 Wearing 支承环45x41x10
Z2113-02515 Bushing 钢背轴承2515
D69K8-70201 Entend & indent fork
30209FT End roller
B6150-00045 Snap ring GB894.1-86
B0230-08040 Bolt GB5782-86
B5050-00008 Washer,lock GB93-87
D10P8-00501 Roller
D69K8-70201 Extend & indent fork 伸缩叉总成
D69K8-70301 Upper & lower bracket 属具起落架
D69K8-70401 Side shift setting 侧移器总成 “见图29
See fig.29″
D69K8-71031 Forfex plate ass’y 内剪刀板总成
D69K8-71081 Forfex plate ass’y 外剪刀板总成
“HRD69K8501
D69K8-50001″ Extend & intend cylinder 伸缩油缸(左) “见图26
See fig.26″
“HRD69K8501
D69K8-50011″ Extend & intend cylinder 伸缩油缸(右) “见图26
See fig.26″
D69K8-73941 Shaft 叉板销轴2
D69K8-75191 Shaft 叉板销轴1
D69K8-71581 Shaft 伸缩油缸销轴总成1
D69K8-71591 Shaft 伸缩油缸销轴总成2
D69K8-71561 Complex roller 属具用复合滚轮
D69K8-71801 Complex roller 属具用复合滚轮
Z2500-00610 Fitting 油杯M6 JB/T 7940.1-1995
B5050-00006 Washer,lock 垫圈6 GB93-87
B0330-06012 Bolt 螺栓M6x12 GB5783-86
D69K8-73631 Buhsing 钢背轴承4030
D69K8-75251 Shaft 叉板连接销轴
D69K8-71571 Shaft 叉板钢背轴承
D69K8-75231 Shaft 伸缩油缸钢背轴承
B4313-00008 Nut 螺母M8 GB6172-86
B0330-08040 Bolt 螺栓M8x40 GB5783-86
Z2513-00610 Fitting 油杯90°M6 JB/T 7940.2-1995
D69K8-73611 Lock cover 锁紧端盖
D69K8-73641 Shim 垫片t3
D69K8-73651 Shim 垫片t1
D69K8-73621 Stopper ring 限位环
D69K8-79001 Pin 销6×50 GB879-86
B1210-06010 Screw 螺钉M6x10 GB818-85
F2B55-12811 Shim 垫片
HRDH3S8418 Shim 调整垫片 DH3S8-49001
D69K8-73821 Cushion block 防撞滑块
B8030-08020 Screw 螺钉M8x20 GB70-85
B5050-00008 Washer 垫圈8 GB93-87
D69K8-70401 Side shift setting 侧移器总成
D69K8-71041 Rear bracket 货叉架后架
D69K8-71061 Front bracket 侧移前架
D69K8-71051 “Tilt Bracket 倾斜支架总成
ass’y(Inc.24-34) (包含24-34)”
B8030-12020 Screw 螺钉M12x20 GB70-85
Q70B0-92131 Plug 螺塞Z1/8” Q/ZB223.1
JT8022-96051 Elbow 直角接头
B8030-12040 Screw 螺钉M12x40 GB70-85
B5050-00012 Washer,lock 垫圈12 GB93-87
Z2500-00610 Fitting 油杯M6 JB/T 7940.1-1995
Q78B0-92181 Lock plate 限位板
D69K8-73301 Sleeve 轴套
D69K8-71091 Shaft ass’y 销轴总成
B8030-10025 Screw 螺钉M10x25 GB70-85
B5050-00010 Washer,lock 垫圈10 GB93-87
D69K8-71601 Tilt cylinder 倾斜油缸 See fig.33
D69K8-75311 Shaft 倾斜油缸顶块销轴
B3010-02010 Pin 销2×10 GB91-86
B5050-00005 Washer,lock 垫圈5 GB93-87
B8030-05025 Screw 螺钉M5x25 GB70-85
Q700B01 Fitting 直通式滑脂嘴
D69K8-73911 Upper block 倾斜油缸顶块
Z2132-02030 Bushing 钢背轴承2030 Q/AC40001-2002
D69K8-73931 Rod 辅助顶杆
D69K8-71151 Tilt bracket 倾斜支架
Q70B0-92121 Upper slip block 上滑块
Q70B0-92141 Side shaft piston rod 侧移活塞杆
Q78B0-92111 Lower slip block 下滑块
Q78B0-92151 Guide 侧移缸盖
Q78B0-92371 O-ring O型密封圈45.69×2.62
Q78B0-92361 U-ring U型密封圈40x48x8
Q78B0-92381 Dust ring 防尘圈40x48x5/7
B6050-00052 Snap ring 挡圈52 GB893.1-86
Q78B0-92351 “Shim φ45 调整垫片
xφ52×0.5″
Q78B0-92151B Snap ring 挡片
HRD69K8303 Inner mast 内门架总成 “见选用表
See option parts”
HRD69K8302 Middle mast 中门架总成 “见选用表
See option parts”
HRD69K8301 Outer mast 外门架总成 “见选用表
See option parts”
B0430-20090 Pin 螺栓M20x1.5×90 GB5785-86
B5050-00020 Washer 垫圈20 GB93-87
B0430-20070 Bolt 螺栓M20x70 GB5783-86
B4223-00020 Fitting 螺母M20x1.5 GB93-87
B0330-08020 Bushing 螺栓M8x20 GB5783-86
B5050-00008 Cap 垫圈8 GB93-87
D69K8-71101 Bolt 防护网总成
D69K8-34501 Washer 调整垫片
D69K8-81011 Roller(lnc.13-16) 组合滚轮(包含13-16)
DA2Q8-70051 Shim 弹性垫圈
CGL209HF Side roller 侧滚轮(含调节螺丝)
B6150-00045 Shafting ring 轴用挡圈
30209FT End roller 主滚轮
D69K8-81021 Roller(lnc.14-16,29) 组合滚轮 (包含14-16,29)
D69K8-81001 Roller(lnc.19-22) 组合滚轮(包含19-22)
DA2Q8-70051 Shim 弹性垫圈
CGLA211 Siae roller 侧滚轮(含调节螺丝)
B6150-00055 Shafting ring 轴用挡圈
80711JT End roller 主滚轮
D69K8-22001 Upper baffle 上缓冲板
B0330-06016 Bolt 螺栓M6x16 GB5783-86
B5050-00006 Washer,lock 垫圈6 GB93-87
B8030-12020 Screw 螺钉M12x20 GB70-85
B5050-00012 Washer,lock 垫圈12 GB93-87
B5310-00012 Washer 垫圈12 GB97.1-86
D69K8-81041 Snap ring 弹性垫圈
HRD69K8401 “Front lift 前起升油缸安装
cylinder mounting”
B5050-00014 Washer,lock 垫圈14 GB93-87
D69K8-42031 Shaft sleeve 缸底轴套
HRLH1244011-N Chain 链条总成
DS2S8-42051 Spacer 隔套短
B6150-00045 Snap ring 挡圈45 GB894.1-86
B0530-12040 Bolt 螺栓M12X1.25X40 GB5786-86
D69K8-41001 Support 前缸固定卡
B0330-14045 Bolt 螺栓M14X45 GB5783-86
HRD69K8402 “Front lift cylinder 前起升油缸
(Inc.13-33) (包含13-33)”
D69K8-75891 Sheave axle 链轮轴
D69K8-75911 Sheave 链轮
D69K8-71911 Sheave seat 链轮座
LB4C-100 Safety valve 安全阀G3/4”
Q70B0-82141 Shim 垫片
B8032-05008 Screw 螺钉M5x8 GB/T70-1985
DA2N8-06A Spring 弹簧
D69K8402-01 Piston rod 柱塞杆
FQ0057C1 Dust ring 防尘圈65X73X5/6.3
GCQ075JND-06 Snap ring 挡片75X65X3
4615900 Shafting ring 605型轴用密封圈65X75X6
AG0075A O-ring O型密封圈75X3.1
DA2N8-05A Screw 紧定螺钉M8x6
D69K8402-02 Guide 导向套
Z6003-07003 O-ring O型密封圈D70X3.1
ED070T-52301 Shim 垫片70x75x1.25
Z1505-0050 Steel ball 钢球5 GB308-1989
D69K8402-03 Piston 活塞
B1832-04006 Screw 紧定螺钉M4x6
DE3K8-42061A Sleeve 套
PN4300750-Z20N “Seal ring 组合密封圈
75×59.5×6.3″
GCQ075DL3-10 Wearing 支承环75x70x20
GCQ055DL4-08 Snap ring 孔用钢丝挡圈
D69K8402.1-00 Cylinder body 缸体
B6150-00032 Snap ring 挡圈32 GB894.1-86
B4123-00016 Nut ;螺母M16x1.5 GB6171-86
LH1244-10011 Washer 球面垫圈
B3010-03030 Pin 开口销3.2×30 GB91-86
HRD69K8403 “Rear lift cylinder 后起升油缸安装
mounting”
B8330-08025 Screw 螺钉M8X25 GB79-85
HRLH1234021-N Chain(lnc.40-42) 链条总成 “见选用件表
See op. Parts”
HRD69K8404 “Rear lift cylinder 后起升油缸
(Inc.21-39) (包含21-39)” “见选用件表
See op. Parts”
DE778-42031 Buffer 减震块
DE778-42061 Shim 调整垫片
DS3Z8-40211 Lock plate ass’y 卡板总成
DS3Z8-42021 Lock plate 卡板
DE778-42041 Mat 垫板 GB6172-86
B4313-00008 Nut 螺母M8
B5050-00010 Washer,lock 垫圈10
B6150-00040 Bolt 螺栓M10X40 GB5785-86
B6150-00040 Snap ring 挡圈40 GB894.1-86
D69K8-42001 Sheave 链轮
“HRD15N8701K
D15N8-42001″ Shim 调整垫片
“HRD15N8701K
D15N8-42011″ Shim 调整垫片
B0330-08016 Bolt 螺栓M8x16 GB895.1-86
B5310-00008 Washer 垫圈8
B5050-00008 Washer,lock 垫圈8
D69K8-42021 Lock plate(right) 后缸限位板(右)
D69K8-42011 Lock plate(left) 后缸限位板(左)
24459-42271 Dust ring 防尘圈45x57x7/10
D30K8-54012 Snap ring 挡片45x55x3
D28B8-42611 Seal ring 轴用密封圈45x55x6
Q78B0-83021 Snap ring 挡片60x54x1.25 GB/T67-2000
C31A7-62072 O-ring O型密封圈53.57×3.53
Z2114-04530 Bushing 钢背轴承4530(t-2.5)
HRD69K8404-02 Guide 导向套
HRD69K8404-01 Piston rod 活塞杆 GB/T80-2000
HRD69K8404.1-00L Cylinderbody L.H. 左缸体
HRD69K8404.1-00R Cylinder body R.H. 右缸体
HRD69K8404-03 Spacer 调整套
B1832-04006 Screw 紧定螺钉M4x6
GS1811V0 “Seal ring SPGO型密封件
55×46.5×3.8″
QUY160.18.17-7 Wearing 支承环55x50x20
GCQ060BYD-03A Sleeve 套
HRD69K8404-04 Piston 活塞
GCQ055DL4-08 Snap ring 钢丝挡圈
LB3C-63 Safety valve 安全阀G1/2”
Q70B0-82141 Shim 垫片
B8032-05008 Screw 螺钉M5x5
22198-40192G Nut 球面螺母
B4223-00018 Nut 螺母M18x1.5 GB6171-86
B3010-3P230 Pin 开口销3.2×30 GB91-86
D69K8-71601 Tilt cylinder 倾斜油缸
D69K8-71611-Y Cylinder body 缸体
GS1818V0 Seal ring 格莱密封圈75x61x6.3
D69K8-71621-Y Piston 活塞体 GB/T810-2000
D69K8-71631-Y Guide 导向套
D69K8-71632 Wearing 支承环45x40x5
23918-52161 Snap ring 轴用密封圈40x50x6
Z6053-07753 O-ring O型密封圈77.5×3.55
FQ0035D0 Dust ring 防尘圈40x48x5/6.5
D69K8-10001 “Lifthigh identify point
setting diagram”
D69K8-12001 Support plate
B0330-06016 Bolt GB5783-86
B5050-00006 Washer,lock GB93-87
D69K8-12021 Induction plate
B0330-08016 Bolt GB5783-86
B5050-00008 Washer,lock GB93-87
Q6H02-40021 Encoder setting 编码器安装(包含8-18)
Q6H02-40031 Encoder bracket
B5050-00005 Washer,lock GB93-87
Q78B2-43311 Shaft 轴
Q70B0-82091 Pulley
Q78B2-43219 Front cover
Q78B2-43220 Rear cover
B0330-08016 Bolt GB5783-86
B5210-00008 Washer GB96-86
B5050-00008 Washer,lock GB93-87
Q78B2-43221 Shim
B1210-05010 Screw GB818-85
Z-6206E Wearing GB/T 276-94
Q69K9-10001 Disposing decal 标牌和油漆布置图
6TY10-00-111 Decal 前移式叉车铭牌
B2180-04006 Rivet 铆钉4X6 GB827-86
6TY40-105-08A Decal,model 型号标牌 1.6t
6TY40-00-964 Decal,model 型号标牌 1.8t
6TY10-00-193 Decal 门架实际承载能力铭牌
6TY40-01-08 Plate,safety 安全标志标牌
6TY40-20-01 “Decal,operating 蓄电池使用注意事项标牌
battery notes”
6TY40-30-01 “Decal,maintenance 保养电池注意事项标牌
battery notes”
6TY40-05-07 Decal,adding hydraulic oil 加液压油标牌
6TY40-03-01 Decal,operating 使用须知标牌
6TY40-02-80 Decal,lubrication chart 润滑系统图标牌
6TY40-15-08 Decal,notice thumb hand注意伤手标牌
6TY40-11-01 Decal 合力叉车标牌
6TY40-00-398 Decal,HELI “HELI”标牌
6TY40-18-26 Decal 起升复合指示标牌
6TY40-10-08 Decal,lift 起吊标牌
6TY40-105-06 Decal 车身标牌（左）
6TY40-105-07 Decal 车身标牌（右）
6TY40-176-01 Decal 合力叉车微信二维码标牌
Q69K9-10011 Disposing decal 标牌和油漆布置图
6TY10-00-114 Decal 前移式叉车铭牌
B2180-04006 Rivet 铆钉4X6 GB827-86
6TY40-105-08A Decal,model 型号标牌 1.6t
6TY40-00-964 Decal,model 型号标牌 1.8t
6TY10-00-195 Decal 门架实际承载能力铭牌
6TY40-01-09 Plate,safety 安全标志标牌
6TY40-20-02 “Decal,operating 蓄电池使用注意事项标牌
battery notes”
6TY40-30-02 “Decal,maintenance 保养电池注意事项标牌
battery notes”
6TY40-05-08 Decal,adding hydraulic oil 加液压油标牌
6TY40-03-02 Decal,operating 使用须知标牌
6TY40-02-81 Decal,lubrication chart 润滑系统图标牌
6TY40-15-09 Decal,notice thumb hand注意伤手标牌
6TY40-11-01 Decal 合力叉车标牌
6TY40-00-398 Decal,HELI “HELI”标牌
6TY40-18-26 Decal 起升复合指示标牌
6TY40-10-09 Decal,lift 起吊标牌
6TY40-105-06 Decal 车身标牌（左）
6TY40-105-07 Decal 车身标牌（右）
6TY40-176-01 Decal 合力叉车微信二维码标牌